How to build a woodworking vise

how to build a woodworking vise

Make a Bench Vise for Woodworking

Plans for this vise:datingfuckdating.com build details here: datingfuckdating.com DIY Woodworking Vise Step 1: Welding a Nut to a Base. I want to use a M16 threaded rod for the linear movement. Therefore I need a nut or Step 2: Welding a T-Piece, a Washer and the Rod. I want to use a T-piece pipe to hold the threaded rod and a wooden rod Step 3: First Test Run. Both parts.

I'm moving my workshop from the cellar into the garage to have more space. I built my own workbench and what's still missing, is a woodworking vise. There are several vise sets online, but I want to build my own one.

In this Instructable you can follow all my steps and hopefully be able to build your own. I want to use a M16 threaded rod for the linear movement. Therefore I need a nut or something threaded to interact with the rod. I decided to weld a M16 nut to a flat plate connector. The flat plate connecter has already some holes to fix this part to the workbench. Unfortunately I don't have a welder so I asked my dad to do this job for me.

I gave him the two parts and you can see what I got back in the second picture : He decided, that it would be better to use a thicker piece of metal for the base plat. So he used a thick old washer and drilled two holes in it. I'm glad he did the welding, but I think my idea with the base plate connector would have worked just as fine. Remember to drill a hole into the plate big enough to let the rod pass through. I want to use a T-piece pipe to hold the threaded rod and a wooden rod later. So back to my dad and his welder.

To fix the rod, we added a small hole through the T-piece and the what is the payment on a 40000 car loan and insert a small bolt. Now you can turn the rod by turning the T-piece.

The washer we added is very important. It will later hold the jaw of the vise and will make it move when you want to open the vise. Both parts are finished. Let's try if everything fits together. Looks very good. The difficult part is done. Now comes some woodworking. So what we need next is a moveable jaw for the vise. My dimensions are 40cm by 15cm, but you can adjust them to your needs.

I use scrap wood I have laying around. I would use some kind of hard wood for the jaws, but unfortunately I don't have enough, but I use a little trick. The core consists of three pieces of roof batten made of spruce. It's too soft in my opinion. To reinforce the surface, I use an old piece of laminate I have left over from our master bedroom flooring. The laminate is very strong and is just perfect for this job.

I simply cut two pieces into the right dimensions. Now I got my laminate-spruce sandwich :. I glue all pieces together using wood glue. After everything is dry, I reinforce the structure by applying some counter-sinked screws on both sides. But this is totally up to you. The glue should be enough I guess. They have a length of 50cm.

You can adjust the length to your needs. I don't have a drill press yet, so I use a rack for my driller to get the holes perpendicular to the surface.

The hole in the middle is for the threaded rod and has to go right through the jaw. I add two more holes for the support pipes. These holes should not go right through. Therefore I use a forstner driller. I insert the copper pipes and mark the middle to the bottom side of the jaw. I use a metal drill to drill two small holes through the wood and the copper pipe.

I insert and counter-sink two screws to mount the pipes to the jaw. This time I need three holes which go right through the workbench. I use my rack to get everything in a right angle. I finish the surface with a sander. Remember the washer, which we welded to the T-piece? Now you'll see its purpose. I need some kind of flange, which will connect the jaw to the rod, but still loose enough to allow rotation.

This allows how to find folder options jaw to move with the rod while opening the vise. I use some scrap piece of laminate and mark a wide enough square in my vase 7cm time 7cm. I find the middle and cut out a round dent using a forstner bit the diameter should be wider than the washer, the depth should be deeper than the thickness of the washer. The dent will later house the washer and must not go right through the laminate.

I use a second smaller forstner bit to cut right through the diameter should be smaller than the washer's and bigger the nut's diameter. I use a handsaw to cut the piece in half so I can mount it to the jaw. I use counter-sinked screws to fix the two flange pieces to the jaw. Make sure that the rod can easily rotate. We are almost finished here. I have to mount the washer and the nut piece to the back of my workbench jaw.

Finally I can insert the copper pipes and the rod into the holes and screw in the threaded rod. You can add some lubricant to the thread. The last step is to build a handle. I use a 2cm wooden rod made of beech. I cut it in 40cm lengths, but feel free to adjust this to your needs. I use two rubber doorstoppers for the ends. I use a screw and a washer for each to mount it to the handle.

This will avoid nasty bump accidents later on and also keeps the rod from falling through the T-piece. Congratulations, everything is done and you are hopefully a proud owner of a new how much to withdraw from retirement funds as well :D I hope you will enjoy building this.

Please let me know your experiences and improvements. Please put photos in the comments. Ok now let's get to business. I did some minor projects with the vise. The holding power is more than enough and I'm really happy with it. I also used it to hold some smaller pieces for my router. It did a great job here, but there are some improvements I would do differently next time or I will add later:.

Thank you Stish. Very nice and easy project for a beginner like me. I will make a few adjustments though with a wider thread bar and solid guide rails as mentioned in previous comments but your idea is great and i will definitely be adding this to my workshop!

The only problem I have is you should have used hardwoods for maximum durability. Some maple would not have been too costly. Over time you will find these things matter in a work bench.

It really gets beat up and a soft wood will not endure as much abuse. You might enjoy this DIY quick-adjust mechanism by Pask, particularly with your fine for a vise threads. Reply 2 years ago. Nice project. The usual screw thread for a vise is a coarse pitch called acme thread. It's also used on adjustable piano stools. Thx for the advice. I also found some one who build a vise from a base jack, which is used on scaffolding.

Yup, the difference is huge, here and in how to cook gravy beef in slow cooker wooden vise I built a lot of time is wasted since the vise jaw doesn't advance that much for each turn Question 2 years ago on Step 8.

I'm curious why you chose hollow copper pipe for the horizontal sliding supports. Does the vise need what percentage of americans are lgbt flex to work properly? Answer 2 years ago.

Step 1: What You Need

Cut two 32 long pieces from the one by six board. Glue the two faces of the 32 boards together to make the front jaw of the vise. The jaw will be 32 by 5? by 1? thick. The jaws of the vise are made with stacks of individual blocks, glued together. Here, the blocks have been cut to rough size: I free-hand drew the curve of the jaw on one block, cut it out on the band saw, then used it as a pattern for the rest. The two longer pieces extend down to join with the horizontal part that slides in and out. My homemade quick release woodworking vise datingfuckdating.com and more details:datingfuckdating.com

Feel free to adjust the dimensions to suit your own needs. The rear jaw is L-shaped. Use a drill press, as the holes need to be straight through. Be as precise as you can to avoid any binding of the screws in the finished vise. Then drill the holes through the rear jaw on your drill press. I decided to make wooden handles for the hex bolt as shown in the picture.

Trim this stick into an octagon. A very easy way to do this is shown in this Instructable:. Be sure the holes are straight down the middle. Insert the hex bolt head first into this hole, make sure the bolt is straight with the octagonal handle, fill the hole with epoxy around the bolt, and let cure. Your handles are done!

I did not use any finish on the bench vise or handles. I plan to sand it down if it needs cleaning. Use some beeswax on the bolt threads and in the thru-holes to make turning the hand screws easier. To use the bench vise clamp the rear jaw to the edge of your workbench, insert the work piece, and tighten the jaws.

Very nice tutorial, I like the Moxon vise, and this is a nice way to make one, though I'm considering building this into the side of my bench as a fixed woodworking vise, instead of buying the common kind. I really like your design for the vise! Reply 5 years ago. I don't see why MDF wouldn't work.

Where did you get the 8 inch bolts? I got the 8" hex bolt at either Lowes or Home Depot. It does not need to be threaded all the way. Reply 5 years ago on Introduction. T-Nuts would be a good choice if you can't find flange nuts. Or use a regular hex nut and cut a hexagonal hole to mount it in the rear jaw. I made one of these and promptly gave it to my friend who had no vise in her shop and was hosting a dovetail class. Off to my lumberyard again! Maybe I will spring for maple this time.

Great project but it struck me? Why not adapt the jaws of the vice to fit the "Workmate" it is sitting on? Two tools in one. While googling that one I also ran across this article from Popular Woodworking that has designs for a Face vise and Tail vise using pipe clamps as well.

Quite slick. Introduction: Make a Bench Vise for Woodworking. By rschoenm Follow. More by the author:. Did you make this project? Share it with us! I Made It! Giant Saw Blade Table! PhuketAussie 3 years ago. Reply Upvote. DanielM 5 years ago. Yonatan24 5 years ago. Or you could buy threaded rod and cut it to any length you need.

BeachsideHank 5 years ago on Introduction. JamesC32 5 years ago on Introduction. Seelos 5 years ago on Introduction. Very nice! Your CAD drawings are clean. What program are you using to make the drawings?

Comments:
20.04.2021 in 16:20 Kaziktilar:
You are the profoundness of clarity.

27.04.2021 in 05:37 Duhn:
Search to google Field of justice